Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.
Cloud BMS provides a library of pre-configured AHU (Air Handling Unit) functional testing workflows. Each workflow commands cooling, heating, dampers, or VFDs, reads sensor response, and scores pass or fail against thresholds.Use this page as a parameter and point-requirements lookup. For how scores are produced, see How to read a score. For deployment order, see the Deployment guide.Select a tab to open the workflow you need.
Cooling operation
Heating operation
Mixed damper operation
VFD operation
This workflow tests an AHU (air handling unit) for its cooling operation. It verifies the AHU is running, eliminates outside sources of heating and cooling, and then commands cooling to confirm the unit can deliver cooled air.
Outcome: This test verifies an AHU’s ability to deliver cooled air when the cooling system is commanded on.
Recommended schedule: Run seasonally (when cooling is first needed) per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.
Point requirements:
Device
Required points
AHU
Discharge Air Pressure, Discharge Air Temperature, Mixed Air Temperature, Return Air Temperature, Cooling Command
Required pre-conditions
AHU Occupancy Mode is Occupied
AHU Duct Pressure exceeds 0.4psi [Pressure Min Threshold]
AHU Return Air Temperature is below 60°F [RAT Cooling Threshold]
If any of these conditions are not met, the workflow stops and the test is archived.
Workflow overview
1 Pre-Condition Check
Verify device is Occupied
Duct Pressure exceeds Pressure Min Threshold
Return Air Temperature below RAT Cooling Threshold
2 Stop Active Heating
Success:Discharge Air Temperature is within 10△°F [Heating - Delta] above Mixed Air Temperature
3 Stop Active Cooling
Success:Discharge Air Temperature is within 10△°F [Cooling - Delta] below Mixed Air Temperature
4 Open Mixed Damper
Success:Mixed Air Temperature is within 5△°F [Ventilation - Delta] below Return Air Temperature
5 Start Cooling
Control: Command Cooling to ON
Success:Discharge Air Temperature is 10△°F [Cooling - Delta] more than Mixed Air Temperature, or if Mixed Air Temperature is not available, Discharge Air Temperature exceeds 45°F [DAT Arb Cooling Threshold]
Tuning parameters
#
Parameter
Description
1
Pressure Min Threshold [0.4psi]
Minimum duct pressure required for the test to begin
2
RAT Cooling Threshold [60°F]
Maximum return air temperature for the loop to provide cooling
3
Loop Diff Pressure Min Threshold [3△°F]
Minimum loop system differential pressure
4
Ventilation Delta [5△°F]
Temperature threshold tolerance for fully open mixed damper (delta below RAT)
5
Cooling Delta [10△°F]
Threshold tolerance for cooling (delta between MAT and DAT)
6
Heating Delta [10△°F]
Threshold tolerance for heating (delta between MAT and DAT)
7
DAT Arb Cooling Threshold [45°F]
DAT below which there is indication of cooling
8
Reaction Time [300sec]
Time to wait for actuators to complete their action
9
Stabilization Time [60sec]
Time to wait for the system to stabilize after a command and conditions are met
10
Measure After [60sec]
Time in seconds to wait before checking feedback readings
If you need assistance with interpreting your results, reach out to the support team at support@kodelabs.com.
This workflow will test an AHU (air handling unit) for its heating operation.
First, we display the initial conditions of the equipment.
Then, KODE performs pre-condition checks to ensure the equipment is ready to be tested.
Once confirmed, KODE will stop cooling by commanding the chilled water valve to close fully.
Then, KODE will stop heating by commanding the steam valve to close fully.
Finally, we will command the steam valve to fully open to restart heating.
Outcome: This test will check an AHU’s ability to deliver heat when its steam valve is fully opened.
Recommended schedule: Run seasonally (when heating is first needed) per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.
Point requirements:
Device
Required points
AHU
Discharge Air Pressure, Discharge Air Temperature, Mixed Air Temperature, Chilled Water Valve Percentage Command, Steam Valve Percentage Command
HHW System
Primary Loop Heating Hot Water Valve Percentage Sensor
Required pre-conditions
AHU Discharge Air Pressure exceeds AHU Minimum Discharge Air Pressure Threshold
HHW System Valve exceeds Minimum HHW System Valve Threshold
Variations: There is a variant of this workflow that works with AHU hot water valves instead of steam valves.
Workflow overview
1 Pre-Condition Check
AHU Discharge Air Pressure exceeds Discharge Air Pressure Minimum
HHW System Valve exceeds HHW Loop Valve Minimum
2 Stop Cooling
Control: Command AHU chilled water valve to CHW Valve Close Command
Success:AHU Discharge Air Temperature ≥ AHU Mixed Air Temperature - Stop Cooling DAT-MAT Differential
3 Stop Heating
Control: Command AHU steam valve to Hot Water Valve Close Command
Success:AHU Discharge Air Temperature ≤ AHU Mixed Air Temperature + Stop Heating DAT-MAT Differential
4 Start Heating
Control: Command AHU steam valve to Hot Water Valve Open Command
Success:AHU Discharge Air Temperature ≥ AHU Mixed Air Temperature + Start Heating DAT-MAT Differential
Tuning parameters
#
Parameter
Description
1
Discharge Air Pressure Minimum
Minimum AHU discharge air pressure required for the test to begin running
2
HHW Loop Valve Minimum
Minimum primary HHW loop valve position for HWS to be considered enabled
3
CHW Valve Close Command
Percentage command to close the chilled water valve when stopping cooling
4
Stop Cooling DAT-MAT Differential
Differential between DAT and MAT for Stop Cooling test to run successfully
5
Hot Water Valve Close Command
Percentage command to close the hot water valve when stopping heating
6
Stop Heating DAT-MAT Differential
Differential between DAT and MAT for Stop Heating test to run successfully
7
Hot Water Valve Open Command
Percentage command to open the hot water valve when starting heating
8
Start Heating DAT-MAT Differential
Differential between DAT and MAT for Start Heating test to run successfully
9
Min Sequence Duration
Minimum length of time in seconds that a sequence should take to execute
10
Max Sequence Duration
Maximum length of time in seconds that a sequence should take to execute
11
Stabilization Time
Time in seconds the program will wait between sequences
If you need assistance with interpreting your results, reach out to the support team at support@kodelabs.com.
This workflow will test an AHU (air handling unit) for its mixed air damper operation.
First, we display the initial conditions of the equipment.
Then, KODE performs pre-condition checks to ensure the equipment is ready to be tested.
Once confirmed, KODE will open the mixed air damper and route 100% outdoor air to the air-handling unit.
Finally, KODE will close the mixed air damper and route 100% return air to the air-handling unit.
Outcome: This test evaluates an AHU’s capability to regulate mixed air temperature by modulating the mixed air damper.
Recommended schedule: Run monthly per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.
Point requirements:
Device
Required points
AHU
Discharge Air Pressure, Outdoor Air Temperature, Mixed Air Temperature, Return Air Temperature
Required pre-conditions
AHU Discharge Air Pressure exceeds AHU Minimum Discharge Air Pressure Threshold
Variations: There is a variant of this workflow that works with AHU outdoor air dampers instead of mixed air dampers.
Workflow overview
1 Pre-Condition Check
AHU Discharge Air Pressure exceeds Discharge Air Pressure Minimum
2 Open Mixed Damper
Control: Command AHU mixed air damper to Open Mixed Air Damper Command
Success:AHU Outdoor Air Temperature - Open MAT-OAT Differential ≤ AHU Mixed Air Temperature ≤ AHU Outdoor Air Temperature + Open MAT-OAT Differential
3 Close Mixed Damper
Control: Command AHU mixed air damper to Close Mixed Air Damper Command
Success:AHU Return Air Temperature - Close MAT-RAT Differential ≤ AHU Mixed Air Temperature ≤ AHU Return Air Temperature + Close MAT-RAT Differential
Tuning parameters
#
Parameter
Description
1
Discharge Air Pressure Minimum
Minimum AHU discharge air pressure required for the test to begin running
2
Open MAT-OAT Differential
Differential between MAT and OAT for Open Mixed Damper test to run successfully
3
Close MAT-RAT Differential
Differential between MAT and RAT for Close Mixed Damper test to run successfully
4
Open Mixed Air Damper Command
Percentage command to open the mixed air damper to allow 100% outdoor air in
5
Close Mixed Air Damper Command
Percentage command to close the mixed air damper to allow 100% return air in
6
Min Sequence Duration
Minimum length of time in seconds that a sequence should take to execute
7
Max Sequence Duration
Maximum length of time in seconds that a sequence should take to execute
8
Stabilization Time
Time in seconds the program will wait between sequences
If you need assistance with interpreting your results, reach out to the support team at support@kodelabs.com.
This workflow tests an AHU (air handling unit) for its variable frequency drive (VFD) operation. It verifies the AHU is running, confirms the unit is maintaining pressure at setpoint, then raises and lowers the duct static pressure setpoint to confirm the VFD responds correctly.
Outcome: This test verifies an AHU’s VFD can track duct static pressure setpoint changes in both directions.
Recommended schedule: Run monthly per AHU. Run when there are pressure or airflow complaints. Run when AHU VFDs are installed, replaced, or reprogrammed.
AHU Duct Pressure exceeds 0.4psi [Pressure Min Threshold]
Duct Static Pressure Sensor is within 5% [Relative Tolerance] of setpoint
If any of these conditions are not met, the workflow stops and the test is archived.
Workflow overview
1 Pre-Condition Check
Verify device is Occupied
Duct Pressure exceeds Pressure Min Threshold
Duct Static Pressure Sensor within Relative Tolerance of setpoint
2 Raise Duct Static Setpoint
Control: Command static pressure setpoint to Relative Modulation above current setpoint
Success:Static pressure sensor reads within Relative Tolerance of new setpoint
3 Lower Duct Static Setpoint
Control: Command static pressure setpoint to Relative Modulation below current setpoint
Success:Static pressure sensor reads within Relative Tolerance of new setpoint
Tuning parameters
#
Parameter
Description
1
Relative Modulation [20%]
Percentage to change the setpoint from its current value
2
Relative Tolerance [5%]
Percentage tolerance between sensor and setpoint after the change to confirm success
3
Nominal Tolerance [0.1psi]
Absolute tolerance between sensor and setpoint after the change to confirm success
4
Pressure Min Threshold [0.4psi]
Minimum duct pressure required for the test to begin
5
Reaction Time [300sec]
Time to wait for actuators to complete their action
6
Stabilization Time [60sec]
Time to wait for the system to stabilize after a command and conditions are met
7
Measure After [60sec]
Time in seconds to wait before checking feedback readings
If you need assistance with interpreting your results, reach out to the support team at support@kodelabs.com.
Next steps
VAV workflows
Explore the VAV workflow library for damper, heating, and airflow tracking tests.
FCU workflows
Explore the FCU workflow library for fan, heating, and cooling tests.
Heat pump workflows
Explore the heat pump workflow for combined heating and cooling tests.
FTT projects
Assign workflows to devices and schedule automated testing.
Last modified on August 19, 2026
Was this page helpful?
{"docsConfig":{"theme":"aspen","$schema":"https://mintlify.com/docs.json","name":"KODE Labs - Product Documentation","colors":{"primary":"#015BFA","light":"#3A9AFF","dark":"#015BFA"},"logo":{"light":"https://mintcdn.com/kodelabs/YfYud6Al4TM68wc2/logo/logo-light.png?fit=max\u0026auto=format\u0026n=YfYud6Al4TM68wc2\u0026q=85\u0026s=00d4ffd6ad7a592e52856804d1a53d12","dark":"https://mintcdn.com/kodelabs/YfYud6Al4TM68wc2/logo/logo-dark.png?fit=max\u0026auto=format\u0026n=YfYud6Al4TM68wc2\u0026q=85\u0026s=a6769f53904d96f5a53ea0c4b3c972d6","href":"/"},"favicon":{"light":"https://mintcdn.com/kodelabs/H3HEEQdnaG21O57-/logo/favicon-light.png?fit=max\u0026auto=format\u0026n=H3HEEQdnaG21O57-\u0026q=85\u0026s=3ae881e353dfb5c2f667e175ec82c799","dark":"https://mintcdn.com/kodelabs/H3HEEQdnaG21O57-/logo/favicon-dark.png?fit=max\u0026auto=format\u0026n=H3HEEQdnaG21O57-\u0026q=85\u0026s=845431bc7d53ce5bf50f56ef53d9137f"},"api":{"params":{"expanded":"closed"},"playground":{"display":"interactive","proxy":true},"examples":{"defaults":"required","languages":["bash","javascript","python","powershell"],"prefill":true,"autogenerate":true},"url":"full"},"appearance":{"default":"light","strict":true},"background":{"color":{"light":"#ffffff","dark":"#121212"}},"navbar":{"links":[{"href":"https://kodelabs.com/contact/","label":"Contact Us"}]},"footer":{"socials":{"x":"https://twitter.com/kodelabs","instagram":"https://www.instagram.com/kode_labs","linkedin":"https://www.linkedin.com/company/kodelabs","youtube":"https://www.youtube.com/channel/UCKCnsgnYtugWxMPzu3UEHkw"},"links":[{"header":"Platform","items":[{"label":"KODE OS","href":"https://kodelabs.com"},{"label":"Integrations","href":"https://kodelabs.com/partners/integrations-library"},{"label":"Security","href":"https://kodelabs.com/security"}]},{"header":"Resources","items":[{"label":"Blog","href":"https://kodelabs.com/blog"},{"label":"Reports \u0026 Guides","href":"https://kodelabs.com/resources"},{"label":"Podcasts \u0026 Webinars","href":"https://kodelabs.com/resources"},{"label":"Case Studies","href":"https://kodelabs.com/case-studies"},{"label":"News","href":"https://kodelabs.com/news"}]},{"header":"Solutions","items":[{"label":"Commercial","href":"https://kodelabs.com/solutions/commercial-real-estate"},{"label":"Corporate","href":"https://kodelabs.com/solutions/corporate"},{"label":"Retail","href":"https://kodelabs.com/solutions/retail"},{"label":"Healthcare","href":"https://kodelabs.com/solutions/healthcare"},{"label":"Education","href":"https://kodelabs.com/solutions/education"}]},{"header":"Company","items":[{"label":"About","href":"https://kodelabs.com/about"},{"label":"Careers","href":"https://kodelabs.com/careers"},{"label":"Internships","href":"https://kodelabs.com/internships"},{"label":"Contact Us","href":"https://kodelabs.com/contact"}]}]},"search":{"prompt":"Search our docs..."},"fonts":{"heading":{"family":"Manrope","weight":600},"body":{"family":"Inter"}},"icons":{"library":"lucide"},"styling":{"eyebrows":"section","codeblocks":{"theme":{"light":"github-light","dark":"github-dark"}},"latex":false},"integrations":{"ga4":{"measurementId":"G-WKYQEE1T4B"}},"banner":{"content":"KODE 3.20 is live. See [what's new in November 2026](/whats-new/2026/v3.20-november-2026).","dismissible":true,"color":{"light":"#015BFA","dark":"#015BFA"}},"errors":{"404":{"redirect":false,"title":"We're working on it!","description":"If you're not seeing this page, we're definitely updating it."}},"contextual":{"options":["copy","view",{"title":"Email KODE support","description":"Contact KODE Labs support for help","icon":"mail","href":"mailto:support@kodelabs.com"}],"display":"toc"},"interaction":{"drilldown":false},"metadata":{"timestamp":true},"navigation":{"global":{"anchors":[{"anchor":"Home","icon":"house","href":"/"},{"anchor":"What's New","icon":"megaphone","href":"/whats-new/2026/v3.20-november-2026"}]},"pages":[]}},"deployment":{"deploymentMetadataValue":{"subdomain":"kodelabs","hasAudioNarration":false,"actualSubdomain":"kodelabs","customDomains":["docs.kodelabs.com"],"gitSource":{"type":"github","owner":"kode-labs","repo":"docs","deployBranch":"main","contentDirectory":"","isPrivate":true,"mountPath":"","label":""},"feedback":{"thumbs":true,"agentFeedback":true},"entitlements":{"AI_CHAT":{"status":"ENABLED"},"REMOVE_BRANDING":{"status":"ENABLED"},"CONTEXTUAL_FEEDBACK":{"status":"ENABLED"},"CODE_SNIPPET_FEEDBACK":{"status":"ENABLED"},"WEB_MCP":{"status":"ENABLED"},"NARRATION":{"status":"ENABLED"}},"buildId":"6af8e4f300819710da52c87a","clientVersion":"0.0.4227","searchFilterCounts":[{"language":"default","tag":"Integrations","count":214},{"language":"default","tag":"All Integrations","count":205},{"language":"default","tag":"KODE API","count":143},{"language":"default","tag":"API reference","count":132},{"language":"default","tag":"EnerG","count":61},{"language":"default","tag":"Meters","count":37},{"language":"default","tag":"Building BI","count":35},{"language":"default","tag":"AssetOps","count":32},{"language":"default","tag":"Cloud BMS","count":31},{"language":"default","tag":"Reference","count":29}],"searchSettings":{"showContentSnippets":true,"isFiltersEnabled":true,"maxResults":10}},"assistantConfig":{"enableStarterQuestions":true,"enableContextualStarterQuestions":true},"basePath":"","hasChatPermissions":true,"hasWebMcpPermissions":true,"toggles":[{"name":"kill-isr","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-rbac-roles","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-mintlify-slack","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-integrations-settings","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"rbac-expansion","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-pr-grouping","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-prefix","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"analytics-v7","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"user-flows-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"no-publish-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-onboarding","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving-live","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"stripTemperatureMiddleware","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"support-platform-pylon-zendesk","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"instant-rollback","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications-server","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-fable","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fixed-ai-action-pricing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automation-resolve-merge-conflict","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"scoped-publishing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"mintql","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"page-level-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-version-history-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"billing-page-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"full-page-search","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workspace-projects","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"assistant-v5","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fork-pr-previews","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"revalidation-jwt","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-sso-scim","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"hobby-abuse-scan","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"dashboard-inbox","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-signup","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-dual-write","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-enabled","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"approve-review-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-metadata","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"sso-setup-deadline-banner","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-serve","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"live-agents","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"starter-pricing","enabled":true,"variant":{"name":"control","enabled":true,"payload":{"type":"string","value":"control"},"feature_enabled":true},"impressionData":false},{"name":"llms-txt-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"wildcard-email-auth","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false}],"googleFontsInlined":true},"customCss":[{"filePath":"custom.css","href":"/_mintlify/custom/kodelabs/fd6257d3326e3afa/custom.css"}]}
{"page":{"pagePath":"products/ftt/ahu-workflows","slug":"/products/ftt/ahu-workflows","pageMetadata":{"title":"AHU workflows","sidebarTitle":"AHU workflows","description":"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.","icon":"wind","keywords":["FTT","AHU","workflows","damper","heating","cooling","VFD","functional testing","Cloud BMS"],"href":"/products/ftt/ahu-workflows"},"description":{"compiledSource":"\"use strict\";\nconst {jsx: _jsx} = arguments[0];\nconst {useMDXComponents: _provideComponents} = arguments[0];\nfunction _createMdxContent(props) {\n const _components = {\n p: \"p\",\n ..._provideComponents(),\n ...props.components\n };\n return _jsx(_components.p, {\n children: \"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\"\n });\n}\nfunction MDXContent(props = {}) {\n const {wrapper: MDXLayout} = {\n ..._provideComponents(),\n ...props.components\n };\n return MDXLayout ? _jsx(MDXLayout, {\n ...props,\n children: _jsx(_createMdxContent, {\n ...props\n })\n }) : _createMdxContent(props);\n}\nreturn {\n default: MDXContent\n};\n","frontmatter":{},"scope":{}},"pageType":"default","mdx":{"mdxSource":{"compiledSource":"\"use strict\";const{Fragment:_Fragment,jsx:_jsx,jsxs:_jsxs}=arguments[0];const{useMDXComponents:_provideComponents}=arguments[0];function _createMdxContent(props){const _components={a:`a`,code:`code`,em:`em`,hr:`hr`,li:`li`,ol:`ol`,p:`p`,strong:`strong`,tbody:`tbody`,td:`td`,th:`th`,thead:`thead`,tr:`tr`,ul:`ul`,..._provideComponents(),...props.components},{Card,CardGroup,Check,Heading,Info,Note,Tab,Table,Tabs,Tip,Warning}=_components;if(!Card)_missingMdxReference(`Card`,true);if(!CardGroup)_missingMdxReference(`CardGroup`,true);if(!Check)_missingMdxReference(`Check`,true);if(!Heading)_missingMdxReference(`Heading`,true);if(!Info)_missingMdxReference(`Info`,true);if(!Note)_missingMdxReference(`Note`,true);if(!Tab)_missingMdxReference(`Tab`,true);if(!Table)_missingMdxReference(`Table`,true);if(!Tabs)_missingMdxReference(`Tabs`,true);if(!Tip)_missingMdxReference(`Tip`,true);if(!Warning)_missingMdxReference(`Warning`,true);return _jsxs(_Fragment,{children:[_jsx(_components.p,{children:`Cloud BMS provides a library of pre-configured AHU (Air Handling Unit) functional testing workflows. Each workflow commands cooling, heating, dampers, or VFDs, reads sensor response, and scores pass or fail against thresholds.`}),`\n`,_jsxs(_components.p,{children:[`Use this page as a parameter and point-requirements lookup. For how scores are produced, see `,_jsx(_components.a,{href:`/products/ftt/test-results#how-to-read-a-score`,children:`How to read a score`}),`. For deployment order, see the `,_jsx(_components.a,{href:`/products/ftt/deployment`,children:`Deployment guide`}),`.`]}),`\n`,_jsx(_components.p,{children:`Select a tab to open the workflow you need.`}),`\n`,_jsx(_components.hr,{}),`\n`,_jsxs(Tabs,{children:[_jsxs(Tab,{title:`Cooling operation`,icon:`snowflake`,id:`cooling-operation`,\"data-child-heading-ids\":`[\"required-pre-conditions\",\"workflow-overview\",\"tuning-parameters\"]`,children:[_jsx(_components.p,{children:_jsx(_components.em,{children:`This workflow tests an AHU (air handling unit) for its cooling operation. It verifies the AHU is running, eliminates outside sources of heating and cooling, and then commands cooling to confirm the unit can deliver cooled air.`})}),_jsx(Check,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Outcome:`}),` This test verifies an AHU’s ability to deliver cooled air when the cooling system is commanded on.`]})}),_jsx(Tip,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Recommended schedule:`}),` Run seasonally (when cooling is first needed) per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.`]})}),_jsxs(Info,{children:[_jsx(_components.p,{children:_jsx(_components.strong,{children:`Point requirements:`})}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`Device`}),_jsx(_components.th,{children:`Required points`})]})}),_jsx(_components.tbody,{children:_jsxs(_components.tr,{children:[_jsx(_components.td,{children:`AHU`}),_jsx(_components.td,{children:`Discharge Air Pressure, Discharge Air Temperature, Mixed Air Temperature, Return Air Temperature, Cooling Command`})]})})]})]}),_jsx(Heading,{level:`3`,id:`required-pre-conditions`,children:`Required pre-conditions`}),_jsxs(_components.ol,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Occupancy Mode`}),` is `,_jsx(_components.code,{children:`Occupied`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Duct Pressure`}),` exceeds `,_jsx(_components.code,{children:`0.4psi`}),` [Pressure Min Threshold]`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Return Air Temperature`}),` is below `,_jsx(_components.code,{children:`60°F`}),` [RAT Cooling Threshold]`]}),`\n`]}),_jsx(Warning,{children:_jsx(_components.p,{children:`If any of these conditions are not met, the workflow stops and the test is archived.`})}),_jsx(Heading,{level:`3`,id:`workflow-overview`,children:`Workflow overview`}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`1 Pre-Condition Check`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[`Verify device is `,_jsx(_components.code,{children:`Occupied`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`Duct Pressure`}),` exceeds `,_jsx(_components.code,{children:`Pressure Min Threshold`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`Return Air Temperature`}),` below `,_jsx(_components.code,{children:`RAT Cooling Threshold`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`2 Stop Active Heating`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Discharge Air Temperature`}),` is within `,_jsx(_components.code,{children:`10△°F`}),` [Heating - Delta] above `,_jsx(_components.em,{children:`Mixed Air Temperature`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`3 Stop Active Cooling`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Discharge Air Temperature`}),` is within `,_jsx(_components.code,{children:`10△°F`}),` [Cooling - Delta] below `,_jsx(_components.em,{children:`Mixed Air Temperature`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`4 Open Mixed Damper`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Mixed Air Temperature`}),` is within `,_jsx(_components.code,{children:`5△°F`}),` [Ventilation - Delta] below `,_jsx(_components.em,{children:`Return Air Temperature`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`5 Start Cooling`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`Cooling`}),` to `,_jsx(_components.code,{children:`ON`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Discharge Air Temperature`}),` is `,_jsx(_components.code,{children:`10△°F`}),` [Cooling - Delta] more than `,_jsx(_components.em,{children:`Mixed Air Temperature`}),`, or if `,_jsx(_components.em,{children:`Mixed Air Temperature`}),` is not available, `,_jsx(_components.em,{children:`Discharge Air Temperature`}),` exceeds `,_jsx(_components.code,{children:`45°F`}),` [DAT Arb Cooling Threshold]`]}),`\n`]}),_jsx(Heading,{level:`3`,id:`tuning-parameters`,children:`Tuning parameters`}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`#`}),_jsx(_components.th,{children:`Parameter`}),_jsx(_components.th,{children:`Description`})]})}),_jsxs(_components.tbody,{children:[_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`1`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Pressure Min Threshold`}),` [0.4psi]`]}),_jsx(_components.td,{children:`Minimum duct pressure required for the test to begin`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`2`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`RAT Cooling Threshold`}),` [60°F]`]}),_jsx(_components.td,{children:`Maximum return air temperature for the loop to provide cooling`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`3`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Loop Diff Pressure Min Threshold`}),` [3△°F]`]}),_jsx(_components.td,{children:`Minimum loop system differential pressure`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`4`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Ventilation Delta`}),` [5△°F]`]}),_jsx(_components.td,{children:`Temperature threshold tolerance for fully open mixed damper (delta below RAT)`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`5`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Cooling Delta`}),` [10△°F]`]}),_jsx(_components.td,{children:`Threshold tolerance for cooling (delta between MAT and DAT)`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`6`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Heating Delta`}),` [10△°F]`]}),_jsx(_components.td,{children:`Threshold tolerance for heating (delta between MAT and DAT)`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`7`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`DAT Arb Cooling Threshold`}),` [45°F]`]}),_jsx(_components.td,{children:`DAT below which there is indication of cooling`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`8`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Reaction Time`}),` [300sec]`]}),_jsx(_components.td,{children:`Time to wait for actuators to complete their action`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`9`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Stabilization Time`}),` [60sec]`]}),_jsx(_components.td,{children:`Time to wait for the system to stabilize after a command and conditions are met`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`10`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Measure After`}),` [60sec]`]}),_jsx(_components.td,{children:`Time in seconds to wait before checking feedback readings`})]})]})]}),_jsx(Note,{children:_jsxs(_components.p,{children:[`If you need assistance with interpreting your results, reach out to the support team at `,_jsx(_components.a,{href:`mailto:support@kodelabs.com`,children:`support@kodelabs.com`}),`.`]})}),_jsx(_components.hr,{})]}),_jsxs(Tab,{title:`Heating operation`,icon:`flame`,id:`heating-operation`,\"data-child-heading-ids\":`[\"required-pre-conditions-2\",\"workflow-overview-2\",\"tuning-parameters-2\"]`,children:[_jsx(_components.p,{children:_jsx(_components.em,{children:`This workflow will test an AHU (air handling unit) for its heating operation.`})}),_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`First, we display the initial conditions of the equipment.`}),`\n`,_jsx(_components.li,{children:`Then, KODE performs pre-condition checks to ensure the equipment is ready to be tested.`}),`\n`,_jsx(_components.li,{children:`Once confirmed, KODE will stop cooling by commanding the chilled water valve to close fully.`}),`\n`,_jsx(_components.li,{children:`Then, KODE will stop heating by commanding the steam valve to close fully.`}),`\n`,_jsx(_components.li,{children:`Finally, we will command the steam valve to fully open to restart heating.`}),`\n`]}),_jsx(Check,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Outcome:`}),` This test will check an AHU’s ability to deliver heat when its steam valve is fully opened.`]})}),_jsx(Tip,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Recommended schedule:`}),` Run seasonally (when heating is first needed) per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.`]})}),_jsxs(Info,{children:[_jsx(_components.p,{children:_jsx(_components.strong,{children:`Point requirements:`})}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`Device`}),_jsx(_components.th,{children:`Required points`})]})}),_jsxs(_components.tbody,{children:[_jsxs(_components.tr,{children:[_jsx(_components.td,{children:`AHU`}),_jsx(_components.td,{children:`Discharge Air Pressure, Discharge Air Temperature, Mixed Air Temperature, Chilled Water Valve Percentage Command, Steam Valve Percentage Command`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{children:`HHW System`}),_jsx(_components.td,{children:`Primary Loop Heating Hot Water Valve Percentage Sensor`})]})]})]})]}),_jsx(Heading,{level:`3`,id:`required-pre-conditions-2`,children:`Required pre-conditions`}),_jsxs(_components.ol,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Discharge Air Pressure`}),` exceeds `,_jsx(_components.code,{children:`AHU Minimum Discharge Air Pressure Threshold`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`HHW System Valve`}),` exceeds `,_jsx(_components.code,{children:`Minimum HHW System Valve Threshold`})]}),`\n`]}),_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Variations:`}),` There is a variant of this workflow that works with AHU hot water valves instead of steam valves.`]}),_jsx(Heading,{level:`3`,id:`workflow-overview-2`,children:`Workflow overview`}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`1 Pre-Condition Check`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Discharge Air Pressure`}),` exceeds `,_jsx(_components.code,{children:`Discharge Air Pressure Minimum`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`HHW System Valve`}),` exceeds `,_jsx(_components.code,{children:`HHW Loop Valve Minimum`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`2 Stop Cooling`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`AHU chilled water valve`}),` to `,_jsx(_components.code,{children:`CHW Valve Close Command`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`AHU Discharge Air Temperature`}),` ≥ `,_jsx(_components.em,{children:`AHU Mixed Air Temperature`}),` - `,_jsx(_components.code,{children:`Stop Cooling DAT-MAT Differential`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`3 Stop Heating`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`AHU steam valve`}),` to `,_jsx(_components.code,{children:`Hot Water Valve Close Command`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`AHU Discharge Air Temperature`}),` ≤ `,_jsx(_components.em,{children:`AHU Mixed Air Temperature`}),` + `,_jsx(_components.code,{children:`Stop Heating DAT-MAT Differential`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`4 Start Heating`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`AHU steam valve`}),` to `,_jsx(_components.code,{children:`Hot Water Valve Open Command`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`AHU Discharge Air Temperature`}),` ≥ `,_jsx(_components.em,{children:`AHU Mixed Air Temperature`}),` + `,_jsx(_components.code,{children:`Start Heating DAT-MAT Differential`})]}),`\n`]}),_jsx(Heading,{level:`3`,id:`tuning-parameters-2`,children:`Tuning parameters`}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`#`}),_jsx(_components.th,{children:`Parameter`}),_jsx(_components.th,{children:`Description`})]})}),_jsxs(_components.tbody,{children:[_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`1`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Discharge Air Pressure Minimum`})}),_jsx(_components.td,{children:`Minimum AHU discharge air pressure required for the test to begin running`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`2`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`HHW Loop Valve Minimum`})}),_jsx(_components.td,{children:`Minimum primary HHW loop valve position for HWS to be considered enabled`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`3`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`CHW Valve Close Command`})}),_jsx(_components.td,{children:`Percentage command to close the chilled water valve when stopping cooling`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`4`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Stop Cooling DAT-MAT Differential`})}),_jsx(_components.td,{children:`Differential between DAT and MAT for Stop Cooling test to run successfully`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`5`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Hot Water Valve Close Command`})}),_jsx(_components.td,{children:`Percentage command to close the hot water valve when stopping heating`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`6`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Stop Heating DAT-MAT Differential`})}),_jsx(_components.td,{children:`Differential between DAT and MAT for Stop Heating test to run successfully`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`7`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Hot Water Valve Open Command`})}),_jsx(_components.td,{children:`Percentage command to open the hot water valve when starting heating`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`8`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Start Heating DAT-MAT Differential`})}),_jsx(_components.td,{children:`Differential between DAT and MAT for Start Heating test to run successfully`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`9`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Min Sequence Duration`})}),_jsx(_components.td,{children:`Minimum length of time in seconds that a sequence should take to execute`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`10`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Max Sequence Duration`})}),_jsx(_components.td,{children:`Maximum length of time in seconds that a sequence should take to execute`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`11`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Stabilization Time`})}),_jsx(_components.td,{children:`Time in seconds the program will wait between sequences`})]})]})]}),_jsx(Note,{children:_jsxs(_components.p,{children:[`If you need assistance with interpreting your results, reach out to the support team at `,_jsx(_components.a,{href:`mailto:support@kodelabs.com`,children:`support@kodelabs.com`}),`.`]})}),_jsx(_components.hr,{})]}),_jsxs(Tab,{title:`Mixed damper operation`,icon:`wind`,id:`mixed-damper-operation`,\"data-child-heading-ids\":`[\"required-pre-conditions-3\",\"workflow-overview-3\",\"tuning-parameters-3\"]`,children:[_jsx(_components.p,{children:_jsx(_components.em,{children:`This workflow will test an AHU (air handling unit) for its mixed air damper operation.`})}),_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`First, we display the initial conditions of the equipment.`}),`\n`,_jsx(_components.li,{children:`Then, KODE performs pre-condition checks to ensure the equipment is ready to be tested.`}),`\n`,_jsx(_components.li,{children:`Once confirmed, KODE will open the mixed air damper and route 100% outdoor air to the air-handling unit.`}),`\n`,_jsx(_components.li,{children:`Finally, KODE will close the mixed air damper and route 100% return air to the air-handling unit.`}),`\n`]}),_jsx(Check,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Outcome:`}),` This test evaluates an AHU’s capability to regulate mixed air temperature by modulating the mixed air damper.`]})}),_jsx(Tip,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Recommended schedule:`}),` Run monthly per AHU. Run when there are comfort complaints in a space or floor. Run when AHUs are installed and/or reprogrammed.`]})}),_jsxs(Info,{children:[_jsx(_components.p,{children:_jsx(_components.strong,{children:`Point requirements:`})}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`Device`}),_jsx(_components.th,{children:`Required points`})]})}),_jsx(_components.tbody,{children:_jsxs(_components.tr,{children:[_jsx(_components.td,{children:`AHU`}),_jsx(_components.td,{children:`Discharge Air Pressure, Outdoor Air Temperature, Mixed Air Temperature, Return Air Temperature`})]})})]})]}),_jsx(Heading,{level:`3`,id:`required-pre-conditions-3`,children:`Required pre-conditions`}),_jsxs(_components.ol,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Discharge Air Pressure`}),` exceeds `,_jsx(_components.code,{children:`AHU Minimum Discharge Air Pressure Threshold`})]}),`\n`]}),_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Variations:`}),` There is a variant of this workflow that works with AHU outdoor air dampers instead of mixed air dampers.`]}),_jsx(Heading,{level:`3`,id:`workflow-overview-3`,children:`Workflow overview`}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`1 Pre-Condition Check`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Discharge Air Pressure`}),` exceeds `,_jsx(_components.code,{children:`Discharge Air Pressure Minimum`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`2 Open Mixed Damper`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`AHU mixed air damper`}),` to `,_jsx(_components.code,{children:`Open Mixed Air Damper Command`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`AHU Outdoor Air Temperature`}),` - `,_jsx(_components.code,{children:`Open MAT-OAT Differential`}),` ≤ `,_jsx(_components.em,{children:`AHU Mixed Air Temperature`}),` ≤ `,_jsx(_components.em,{children:`AHU Outdoor Air Temperature`}),` + `,_jsx(_components.code,{children:`Open MAT-OAT Differential`})]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`3 Close Mixed Damper`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`AHU mixed air damper`}),` to `,_jsx(_components.code,{children:`Close Mixed Air Damper Command`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`AHU Return Air Temperature`}),` - `,_jsx(_components.code,{children:`Close MAT-RAT Differential`}),` ≤ `,_jsx(_components.em,{children:`AHU Mixed Air Temperature`}),` ≤ `,_jsx(_components.em,{children:`AHU Return Air Temperature`}),` + `,_jsx(_components.code,{children:`Close MAT-RAT Differential`})]}),`\n`]}),_jsx(Heading,{level:`3`,id:`tuning-parameters-3`,children:`Tuning parameters`}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`#`}),_jsx(_components.th,{children:`Parameter`}),_jsx(_components.th,{children:`Description`})]})}),_jsxs(_components.tbody,{children:[_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`1`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Discharge Air Pressure Minimum`})}),_jsx(_components.td,{children:`Minimum AHU discharge air pressure required for the test to begin running`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`2`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Open MAT-OAT Differential`})}),_jsx(_components.td,{children:`Differential between MAT and OAT for Open Mixed Damper test to run successfully`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`3`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Close MAT-RAT Differential`})}),_jsx(_components.td,{children:`Differential between MAT and RAT for Close Mixed Damper test to run successfully`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`4`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Open Mixed Air Damper Command`})}),_jsx(_components.td,{children:`Percentage command to open the mixed air damper to allow 100% outdoor air in`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`5`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Close Mixed Air Damper Command`})}),_jsx(_components.td,{children:`Percentage command to close the mixed air damper to allow 100% return air in`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`6`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Min Sequence Duration`})}),_jsx(_components.td,{children:`Minimum length of time in seconds that a sequence should take to execute`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`7`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Max Sequence Duration`})}),_jsx(_components.td,{children:`Maximum length of time in seconds that a sequence should take to execute`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`8`}),_jsx(_components.td,{children:_jsx(_components.code,{children:`Stabilization Time`})}),_jsx(_components.td,{children:`Time in seconds the program will wait between sequences`})]})]})]}),_jsx(Note,{children:_jsxs(_components.p,{children:[`If you need assistance with interpreting your results, reach out to the support team at `,_jsx(_components.a,{href:`mailto:support@kodelabs.com`,children:`support@kodelabs.com`}),`.`]})}),_jsx(_components.hr,{})]}),_jsxs(Tab,{title:`VFD operation`,icon:`gauge`,id:`vfd-operation`,\"data-child-heading-ids\":`[\"required-pre-conditions-4\",\"workflow-overview-4\",\"tuning-parameters-4\"]`,children:[_jsx(_components.p,{children:_jsx(_components.em,{children:`This workflow tests an AHU (air handling unit) for its variable frequency drive (VFD) operation. It verifies the AHU is running, confirms the unit is maintaining pressure at setpoint, then raises and lowers the duct static pressure setpoint to confirm the VFD responds correctly.`})}),_jsx(Check,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Outcome:`}),` This test verifies an AHU’s VFD can track duct static pressure setpoint changes in both directions.`]})}),_jsx(Tip,{children:_jsxs(_components.p,{children:[_jsx(_components.strong,{children:`Recommended schedule:`}),` Run monthly per AHU. Run when there are pressure or airflow complaints. Run when AHU VFDs are installed, replaced, or reprogrammed.`]})}),_jsxs(Info,{children:[_jsx(_components.p,{children:_jsx(_components.strong,{children:`Point requirements:`})}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`Device`}),_jsx(_components.th,{children:`Required points`})]})}),_jsx(_components.tbody,{children:_jsxs(_components.tr,{children:[_jsx(_components.td,{children:`AHU`}),_jsx(_components.td,{children:`Duct Static Pressure Sensor, Duct Static Pressure Setpoint`})]})})]})]}),_jsx(Heading,{level:`3`,id:`required-pre-conditions-4`,children:`Required pre-conditions`}),_jsxs(_components.ol,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Occupancy Mode`}),` is `,_jsx(_components.code,{children:`Occupied`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`AHU Duct Pressure`}),` exceeds `,_jsx(_components.code,{children:`0.4psi`}),` [Pressure Min Threshold]`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`Duct Static Pressure Sensor`}),` is within `,_jsx(_components.code,{children:`5%`}),` [Relative Tolerance] of setpoint`]}),`\n`]}),_jsx(Warning,{children:_jsx(_components.p,{children:`If any of these conditions are not met, the workflow stops and the test is archived.`})}),_jsx(Heading,{level:`3`,id:`workflow-overview-4`,children:`Workflow overview`}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`1 Pre-Condition Check`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[`Verify device is `,_jsx(_components.code,{children:`Occupied`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`Duct Pressure`}),` exceeds `,_jsx(_components.code,{children:`Pressure Min Threshold`})]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.em,{children:`Duct Static Pressure Sensor`}),` within `,_jsx(_components.code,{children:`Relative Tolerance`}),` of setpoint`]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`2 Raise Duct Static Setpoint`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`static pressure setpoint`}),` to `,_jsx(_components.code,{children:`Relative Modulation`}),` above current setpoint`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Static pressure sensor`}),` reads within `,_jsx(_components.code,{children:`Relative Tolerance`}),` of new setpoint`]}),`\n`]}),_jsx(_components.p,{children:_jsx(_components.strong,{children:`3 Lower Duct Static Setpoint`})}),_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Control:`}),` Command `,_jsx(_components.em,{children:`static pressure setpoint`}),` to `,_jsx(_components.code,{children:`Relative Modulation`}),` below current setpoint`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Success:`}),` `,_jsx(_components.em,{children:`Static pressure sensor`}),` reads within `,_jsx(_components.code,{children:`Relative Tolerance`}),` of new setpoint`]}),`\n`]}),_jsx(Heading,{level:`3`,id:`tuning-parameters-4`,children:`Tuning parameters`}),_jsxs(Table,{children:[_jsx(_components.thead,{children:_jsxs(_components.tr,{children:[_jsx(_components.th,{children:`#`}),_jsx(_components.th,{children:`Parameter`}),_jsx(_components.th,{children:`Description`})]})}),_jsxs(_components.tbody,{children:[_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`1`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Relative Modulation`}),` [20%]`]}),_jsx(_components.td,{children:`Percentage to change the setpoint from its current value`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`2`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Relative Tolerance`}),` [5%]`]}),_jsx(_components.td,{children:`Percentage tolerance between sensor and setpoint after the change to confirm success`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`3`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Nominal Tolerance`}),` [0.1psi]`]}),_jsx(_components.td,{children:`Absolute tolerance between sensor and setpoint after the change to confirm success`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`4`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Pressure Min Threshold`}),` [0.4psi]`]}),_jsx(_components.td,{children:`Minimum duct pressure required for the test to begin`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`5`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Reaction Time`}),` [300sec]`]}),_jsx(_components.td,{children:`Time to wait for actuators to complete their action`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`6`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Stabilization Time`}),` [60sec]`]}),_jsx(_components.td,{children:`Time to wait for the system to stabilize after a command and conditions are met`})]}),_jsxs(_components.tr,{children:[_jsx(_components.td,{\"data-numeric\":`true`,children:`7`}),_jsxs(_components.td,{children:[_jsx(_components.code,{children:`Measure After`}),` [60sec]`]}),_jsx(_components.td,{children:`Time in seconds to wait before checking feedback readings`})]})]})]}),_jsx(Note,{children:_jsxs(_components.p,{children:[`If you need assistance with interpreting your results, reach out to the support team at `,_jsx(_components.a,{href:`mailto:support@kodelabs.com`,children:`support@kodelabs.com`}),`.`]})})]})]}),`\n`,_jsx(Heading,{level:`2`,id:`next-steps`,children:`Next steps`}),`\n`,_jsxs(CardGroup,{cols:2,children:[_jsx(Card,{title:`VAV workflows`,icon:`fan`,href:`/products/ftt/vav-workflows`,arrow:true,children:_jsx(_components.p,{children:`Explore the VAV workflow library for damper, heating, and airflow tracking tests.`})}),_jsx(Card,{title:`FCU workflows`,icon:`thermometer`,href:`/products/ftt/fcu-workflows`,arrow:true,children:_jsx(_components.p,{children:`Explore the FCU workflow library for fan, heating, and cooling tests.`})}),_jsx(Card,{title:`Heat pump workflows`,icon:`flame`,href:`/products/ftt/hp-workflows`,arrow:true,children:_jsx(_components.p,{children:`Explore the heat pump workflow for combined heating and cooling tests.`})}),_jsx(Card,{title:`FTT projects`,icon:`folder-kanban`,href:`/products/ftt/projects`,arrow:true,children:_jsx(_components.p,{children:`Assign workflows to devices and schedule automated testing.`})})]})]})}function MDXContent(props={}){const{wrapper:MDXLayout}={..._provideComponents(),...props.components};return MDXLayout?_jsx(MDXLayout,{...props,children:_jsx(_createMdxContent,{...props})}):_createMdxContent(props)}return{default:MDXContent};function _missingMdxReference(id,component){throw new Error(`Expected `+(component?`component`:`object`)+\" `\"+id+\"` to be defined: you likely forgot to import, pass, or provide it.\")}","frontmatter":{},"scope":{"codeStyling":{"theme":{"light":"github-light","dark":"github-dark"}},"config":{},"pageMetadata":{"title":"AHU workflows","sidebarTitle":"AHU workflows","description":"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.","icon":"wind","keywords":["FTT","AHU","workflows","damper","heating","cooling","VFD","functional testing","Cloud BMS"],"href":"/products/ftt/ahu-workflows"}}},"mdxSourceWithNoJs":null},"mdxExtracts":{"tableOfContents":[{"title":"Required pre-conditions","slug":"required-pre-conditions","depth":3,"children":[],"tabId":"cooling-operation"},{"title":"Workflow overview","slug":"workflow-overview","depth":3,"children":[],"tabId":"cooling-operation"},{"title":"Tuning parameters","slug":"tuning-parameters","depth":3,"children":[],"tabId":"cooling-operation"},{"title":"Required pre-conditions","slug":"required-pre-conditions-2","depth":3,"children":[],"tabId":"heating-operation"},{"title":"Workflow overview","slug":"workflow-overview-2","depth":3,"children":[],"tabId":"heating-operation"},{"title":"Tuning parameters","slug":"tuning-parameters-2","depth":3,"children":[],"tabId":"heating-operation"},{"title":"Required pre-conditions","slug":"required-pre-conditions-3","depth":3,"children":[],"tabId":"mixed-damper-operation"},{"title":"Workflow overview","slug":"workflow-overview-3","depth":3,"children":[],"tabId":"mixed-damper-operation"},{"title":"Tuning parameters","slug":"tuning-parameters-3","depth":3,"children":[],"tabId":"mixed-damper-operation"},{"title":"Required pre-conditions","slug":"required-pre-conditions-4","depth":3,"children":[],"tabId":"vfd-operation"},{"title":"Workflow overview","slug":"workflow-overview-4","depth":3,"children":[],"tabId":"vfd-operation"},{"title":"Tuning parameters","slug":"tuning-parameters-4","depth":3,"children":[],"tabId":"vfd-operation"},{"title":"Next steps","slug":"next-steps","depth":2,"children":[]}],"codeExamples":{}},"jsLinks":["/_mintlify/custom/kodelabs/ce5d3bd08e955b7b/navbar-assistant.js"],"subdomain":"kodelabs","siteName":"KODE Labs - Product Documentation","title":"AHU workflows - KODE Labs - Product Documentation","contextualStarterQuestions":[{"_id":"6a88bb8b1af966f81de13e20","deploymentId":"67fd4d9635f314f3a994be65","questionText":"What points do AHUs need?","status":"active","generatedBy":"contextual","path":"products/ftt/ahu-workflows","createdAt":"2026-08-21T20:56:43.201Z","updatedAt":"2026-08-21T20:56:43.201Z","__v":0},{"_id":"6a88bb8b1af966f81de13e22","deploymentId":"67fd4d9635f314f3a994be65","questionText":"What are the test preconditions?","status":"active","generatedBy":"contextual","path":"products/ftt/ahu-workflows","createdAt":"2026-08-21T20:56:43.201Z","updatedAt":"2026-08-21T20:56:43.201Z","__v":0},{"_id":"6a88bb8b1af966f81de13e21","deploymentId":"67fd4d9635f314f3a994be65","questionText":"When should I run cooling tests?","status":"active","generatedBy":"contextual","path":"products/ftt/ahu-workflows","createdAt":"2026-08-21T20:56:43.201Z","updatedAt":"2026-08-21T20:56:43.201Z","__v":0}],"navMaps":{"firstHrefInVersion":{},"firstHrefInLanguage":{}},"lastModified":"2026-08-19T11:09:35.749Z","gitLastModified":"2026-08-19T11:07:50.000Z","originalFileLocation":"products/ftt/ahu-workflows.mdx"},"headHtml":"\u003cscript data-mint-head>(function(){var d=document.documentElement,p=\"light\";if(!p){try{p=localStorage.getItem(\"isDarkMode\")}catch(e){}if(p==='true')p='dark';else if(p==='false')p='light';if(p!=='light'\u0026\u0026p!=='dark'\u0026\u0026p!=='system')p=\"light\"}var r=p==='system'?(matchMedia(\"(prefers-color-scheme: dark)\").matches?'dark':'light'):p;d.classList.remove(r==='dark'?'light':'dark');d.classList.add(r);d.setAttribute(\"data-theme-preference\",p)})();\u003c/script>\u003cmeta data-mint-head name=\"description\" content=\"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\">\u003cmeta data-mint-head name=\"application-name\" content=\"KODE Labs - Product Documentation\">\u003cmeta data-mint-head name=\"generator\" content=\"Mintlify\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/android-chrome-192x192.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"apple-touch-icon\" type=\"image/png\" sizes=\"180x180\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/apple-touch-icon.png\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/favicon-16x16.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/favicon-32x32.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/favicon.ico\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon-dark/android-chrome-192x192.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon-dark/favicon-16x16.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon-dark/favicon-32x32.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon-dark/favicon.ico\" media=\"(prefers-color-scheme: dark)\">\u003cmeta data-mint-head property=\"og:title\" content=\"AHU workflows - KODE Labs - Product Documentation\">\u003cmeta data-mint-head property=\"og:description\" content=\"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\">\u003cmeta data-mint-head property=\"og:site_name\" content=\"KODE Labs - Product Documentation\">\u003cmeta data-mint-head property=\"og:url\" content=\"https://docs.kodelabs.com/products/ftt/ahu-workflows\">\u003cmeta data-mint-head property=\"og:type\" content=\"website\">\u003cmeta data-mint-head property=\"og:image\" content=\"https://kodelabs.mintlify.site/_mintlify/api/og/v2?division=Workflow+library\u0026amp;title=AHU+workflows\u0026amp;description=Reference+for+all+AHU+functional+testing+workflows+including+cooling+operation%2C+heating+operation%2C+mixed+damper+operation%2C+and+VFD+operation+tests.\u0026amp;theme=ac252318c016362b89abdbd3\u0026amp;signature=4ca669c4d01c0145cd1dab02dca68cbf9eb05b3123928b21a35893b397c929d9\">\u003cmeta data-mint-head property=\"og:image:width\" content=\"1200\">\u003cmeta data-mint-head property=\"og:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"twitter:card\" content=\"summary_large_image\">\u003cmeta data-mint-head name=\"twitter:title\" content=\"AHU workflows - KODE Labs - Product Documentation\">\u003cmeta data-mint-head name=\"twitter:description\" content=\"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\">\u003cmeta data-mint-head name=\"twitter:image\" content=\"https://kodelabs.mintlify.site/_mintlify/api/og/v2?division=Workflow+library\u0026amp;title=AHU+workflows\u0026amp;description=Reference+for+all+AHU+functional+testing+workflows+including+cooling+operation%2C+heating+operation%2C+mixed+damper+operation%2C+and+VFD+operation+tests.\u0026amp;theme=ac252318c016362b89abdbd3\u0026amp;signature=4ca669c4d01c0145cd1dab02dca68cbf9eb05b3123928b21a35893b397c929d9\">\u003cmeta data-mint-head name=\"twitter:image:width\" content=\"1200\">\u003cmeta data-mint-head name=\"twitter:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"msapplication-config\" content=\"/mintlify-assets/_mintlify/favicons/kodelabs/vtcGE1gj2AkAE1l2/_generated/favicon/browserconfig.xml\">\u003cmeta data-mint-head name=\"apple-mobile-web-app-title\" content=\"KODE Labs - Product Documentation\">\u003cmeta data-mint-head name=\"msapplication-TileColor\" content=\"#015BFA\">\u003clink data-mint-head rel=\"canonical\" href=\"https://docs.kodelabs.com/products/ftt/ahu-workflows\">\u003clink data-mint-head rel=\"alternate\" type=\"application/xml\" href=\"/sitemap.xml\">\u003clink data-mint-head rel=\"alternate\" type=\"text/markdown\" href=\"/products/ftt/ahu-workflows.md\">\u003cscript data-mint-head type=\"application/ld+json\">{\"@context\":\"https://schema.org\",\"@graph\":[{\"@type\":\"Organization\",\"@id\":\"https://docs.kodelabs.com/#organization\",\"name\":\"KODE Labs - Product Documentation\",\"url\":\"https://docs.kodelabs.com\",\"logo\":{\"@type\":\"ImageObject\",\"url\":\"https://mintcdn.com/kodelabs/YfYud6Al4TM68wc2/logo/logo-light.png?fit=max\u0026auto=format\u0026n=YfYud6Al4TM68wc2\u0026q=85\u0026s=00d4ffd6ad7a592e52856804d1a53d12\"}},{\"@type\":\"WebSite\",\"@id\":\"https://docs.kodelabs.com#website\",\"name\":\"KODE Labs - Product Documentation\",\"url\":\"https://docs.kodelabs.com\",\"publisher\":{\"@id\":\"https://docs.kodelabs.com/#organization\"}},{\"@type\":\"WebPage\",\"@id\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows#webpage\",\"url\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows\",\"name\":\"AHU workflows\",\"description\":\"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\",\"dateModified\":\"2026-08-19T11:07:50.000Z\",\"isPartOf\":{\"@id\":\"https://docs.kodelabs.com#website\"},\"breadcrumb\":{\"@id\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows#breadcrumb\"}},{\"@type\":\"BreadcrumbList\",\"@id\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Workflows\",\"item\":\"https://docs.kodelabs.com/products/ftt/workflows\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Workflow library\",\"item\":\"https://docs.kodelabs.com/products/ftt/vav-workflows\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"AHU workflows\",\"item\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows\"}]},{\"@type\":[\"Article\",\"TechArticle\"],\"@id\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows#article\",\"headline\":\"AHU workflows\",\"name\":\"AHU workflows\",\"description\":\"Reference for all AHU functional testing workflows including cooling operation, heating operation, mixed damper operation, and VFD operation tests.\",\"url\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows\",\"mainEntityOfPage\":{\"@id\":\"https://docs.kodelabs.com/products/ftt/ahu-workflows#webpage\"},\"dateModified\":\"2026-08-19T11:07:50.000Z\",\"keywords\":\"FTT, AHU, workflows, damper, heating, cooling, VFD, functional testing, Cloud BMS\",\"publisher\":{\"@id\":\"https://docs.kodelabs.com/#organization\"},\"isPartOf\":{\"@id\":\"https://docs.kodelabs.com#website\"}}]}\u003c/script>","agentPointerHref":"/products/ftt/ahu-workflows.md","siteName":"KODE Labs - Product Documentation","nav":{"global":{"anchors":[{"anchor":"Home","icon":"house","href":"/"},{"anchor":"What's New","icon":"megaphone","href":"/whats-new/2026/v3.20-november-2026"}]},"products":[{"product":"Cloud BMS","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/cloud-bms.svg","description":"Cloud building management, graphics, and control","pages":[{"title":"Cloud BMS","href":"/products/kode-os/get-started/introduction"}]},{"product":"Building BI","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/bbi.svg","description":"Dashboards and analytics for building performance","pages":[{"title":"Building BI","href":"/products/building-bi/overview"}]},{"product":"FDD","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/fdd.svg","description":"Fault detection and diagnostics for equipment","pages":[{"title":"FDD","href":"/products/fdd/overview"}]},{"product":"FTT","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/ftt.svg","description":"Automated functional testing and commissioning","groups":[{"group":"Get Started","pages":[{"title":"What is Functional Testing?","sidebarTitle":"Introduction","icon":"rocket","href":"/products/ftt/overview"}]},{"group":"Testing","pages":[{"title":"Test results","sidebarTitle":"Test results","icon":"list-checks","href":"/products/ftt/test-results"},{"title":"FTT projects","sidebarTitle":"Projects","icon":"clipboard-list","href":"/products/ftt/projects"}]},{"group":"Workflows","pages":[{"title":"Workflows","sidebarTitle":"Workflows","icon":"workflow","href":"/products/ftt/workflows"},{"title":"Workflow logic blocks","sidebarTitle":"Logic blocks","icon":"puzzle","href":"/products/ftt/workflow-logic-blocks"},{"title":"Workflow creator guide","sidebarTitle":"Creator guide","icon":"drafting-compass","href":"/products/ftt/workflow-creator-guide"},{"group":"Workflow library","icon":"library","expanded":false,"pages":[{"title":"VAV workflow library","sidebarTitle":"VAV workflows","icon":"fan","href":"/products/ftt/vav-workflows"},{"title":"FCU workflow library","sidebarTitle":"FCU workflows","description":"Reference for all FCU functional testing workflows including fan operation, heating and cooling tests with and without fan verification, and FCU cooling operation.","icon":"thermometer","href":"/products/ftt/fcu-workflows"},{"title":"AHU workflows","sidebarTitle":"AHU workflows","icon":"wind","href":"/products/ftt/ahu-workflows"},{"title":"Heat pump workflow library","sidebarTitle":"HP workflows","description":"Reference for the heat pump functional testing workflow covering combined heating and cooling operation with fan verification.","icon":"flame","href":"/products/ftt/hp-workflows"}]}]},{"group":"Deployment","pages":[{"title":"Deployment guide","sidebarTitle":"Deployment","icon":"rocket","href":"/products/ftt/deployment"}]},{"group":"Reference","icon":"book-a","pages":[{"title":"KODE glossary","sidebarTitle":"Glossary","icon":"book-a","href":"/products/ftt/glossary"}]}]},{"product":"AssetOps","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/assetops.svg","description":"Asset and maintenance operations","pages":[{"title":"AssetOps","href":"/products/assetops/quickstart/overview"}]},{"product":"EnerG","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/enerG.svg","description":"Energy management and sustainability reporting","pages":[{"title":"EnerG","href":"/products/energ/get-started/introduction"}]},{"product":"Launchpad","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/launchpad.svg","description":"Dynamic management for apps, users, and buildings","pages":[{"title":"Launchpad","href":"/products/launchpad/get-started/introduction"}]},{"product":"Mobile app","icon":"https://mintlify.s3.us-west-1.amazonaws.com/kodelabs/images/mobile-app.svg","description":"Monitor and operate buildings from iOS and Android","pages":[{"title":"Mobile app","href":"/products/mobile-app/overview"}]},{"product":"KODE API","icon":"braces","description":"Build services and integrations with KODE OS","pages":[{"title":"KODE API","href":"/products/kode-api"}]},{"product":"Integrations","icon":"cable","description":"Connect 200+ building systems to KODE OS","pages":[{"title":"Integrations","href":"/products/integrations/get-started/introduction"}]},{"product":"What's New","icon":"megaphone","description":"KODE platform release notes and updates","pages":[{"title":"What's New","href":"/whats-new/2026/v3.20-november-2026"}]}]},"basePath":"","title":"AHU workflows - KODE Labs - Product Documentation","deploymentId":"dpl_vSEmv961Ncyvz1psVwgUnTXQMSYk","buildId":"dpl_vSEmv961Ncyvz1psVwgUnTXQMSYk","dynamics":["10e4515597"],"chunks":["BannerMarkdown-DnSAhvaM.js","dist-DIfYWxfm.js","lib-DMeTj1gb.js","lib-B8HbPgcC.js","katex-Dbtb6Wk7.js","html-void-elements-mCSPHezU.js","marked.esm-CZWythHk.js"]}